全國服務熱線
13953181568
濟南車庫門（電動）行程間距如何調理更標準
How to adjust the distance of Jinan garage door (electric) more standard電動車庫門的行程間隔不精確會影響到電動車庫門的運用，找專業的車庫門廠家調整需求的費用會很多，因而，本人手動停止調整也是能夠的。電動車庫門行程間隔的調整按以下步驟停止即可。
The imprecise travel interval of the electric garage door will affect the use of the electric garage door. It will cost a lot to find a professional garage door manufacturer to adjust the demand. Therefore, it is also possible for me to stop adjusting manually. The adjustment of the travel interval of the electric garage door can be stopped by following steps.
1、按下控制板上的FUNC鍵，此時RUN燈開端閃動，按住此鍵超越8秒，RUN燈變?yōu)槌Ａ粒藭r程序進入開關門行程和過載力學習過程；2、按INC鍵時 電機開端向開門的方向運轉，按住不放，電機運轉速度由慢轉快，同時RUN指示燈閃亮，標明電機向上運轉。抵達理想的位置后松開按鍵，電機中止運轉；假如按下DEC鍵，則電機由慢轉快向關門方向運轉，STA燈閃亮。用這兩個按鍵可調理上行位置。
1. Press the FUNC key on the control board, then the RUN light starts to flicker. Press and hold this key for more than 8 seconds, and the RUN light becomes constant. At this time, the program enters the learning process of switching and overloading. 2. When press the INC key, the motor starts to run in the direction of opening, press and hold, and the speed of the motor turns from slow to fast. At the same time, the RUN light flashes, indicating that the motor runs upward. After reaching the ideal position, release the button, and the motor will stop running. If the DEC key is pressed, the motor will turn from slow to fast to close, and the STA lamp will shine. Use these two keys to adjust the upstream position.
濟南車庫門
Jinan Garage Gate
濟南車庫門
3、假如上行位置調整適宜后，按FUNC鍵一次，則RUN指示燈快速閃爍后熄滅，標明上到位學習完成；同時STA指示燈點亮，程序進入下到位學習過程；4、用 INC 和 DEC兩個按鍵調整下到位位置，在抵達預定位置后，按FUNC鍵一次，STA燈閃亮，標明下到位完成；5、上下到位位置調整終了，程序自動進入開關門力氣：門體首先向開門的方向運轉，同時RUN燈點亮，在門體運轉過程中，程序自動丈量運轉中門體所遭到的阻力，抵達上到位后自動中止，延時一段時間后，程序自動關門，此時STA燈點亮，程序丈量關門時的力氣，抵達下到位后，自動中止；6、按遙控器上的按鍵或墻壁開打開的按鍵，電機依照請求正常運轉。
3. If the upstream position is adjusted properly, press the FUNC key once, then the RUN indicator flashes quickly and then goes out, indicating that the upper-position learning is completed; at the same time, the STA indicator lights up and the program enters the lower-position learning process; 4. Adjust the lower-position with the INC and DEC keys, and press the FUNC key once after reaching the predetermined position, the STA lamp flashes, indicating that the lower-position is completed; 5. Upper-lower-position learning is completed; At the end of the position adjustment, the program automatically enters the power of the door: the door body first moves towards the direction of opening, and the RUN lamp lights up. In the process of the door body operation, the program automatically measures the resistance of the door body in operation, automatically stops after reaching the upper position, and automatically closes the door after a delay period of time. At this time, the STA lamp lights up, the program measures the force of closing the door, after reaching the lower position. 6. Press the button on the remote controller or open the button on the wall, and the motor will run normally according to the request.